Bubble size
The bubble size of a gas to be dissolved in a liquid affects the solubility of the same. The gas exchange area increases with decreasing...
Weiterlesen
Bubble size
The bubble size of a gas to be dissolved in a liquid affects the solubility of the same. The gas exchange area increases with decreasing...
Weiterlesen
Burst tolerance
The burst tolerance refers to the range in which a bursting disc is allowed to react in deviation from the nominal bursting pressure. This is...
Weiterlesen
Bursting disc
A bursting disc unit is a pressure relief device which is typically made up of a bursting disc and a bursting disc holder. The bursting...
Weiterlesen
Bursting pressure
Differential pressure between inlet and outlet side of the bursting disc at which the bursting disc opens and frees the flow cross section. The bursting...
Weiterlesen
Bursting temperature
The bursting temperature is the temperature assigned to a bursting pressure corresponding to the expected temperature of the bursting disc at the time of reaction....
Weiterlesen
Composite bursting disc
Multilayer (stainless steel / PTFE / stainless steel) built up metal bursting disc for direct installation between flanges (without bursting disc holder). Composite bursting discs...
Weiterlesen
Concave bursting disc
Forward acting, arched bursting disc with the pressure being directed against the concave side...
Weiterlesen
Convex bursting disc
Pressure-loaded, arched bursting disc (also known as “reverse acting rupture disc”) with the pressure being directed against the convex side...
Weiterlesen
Design code
The design code refers to the design standard of pressure equipment. The pressure equipment from STRIKO process technology are manufactured in accordance with the applicable...
Weiterlesen
Design data
In the field of technology, this term refers to the preliminary information required in order to be able to build or design equipment or components...
Weiterlesen
Design pressure
The pressure equipment directive (PED, German abbreviation DGRL) classifies pressure equipment into various categories depending on the pressure equipment volume V respectively the nominal size...
Weiterlesen
Design standard
STRIKO process technology provides new and existing customers with special forms for inquiry specification in which the customer, alongside the general information, also specifies the...
Weiterlesen
Documentation, technical
A technical documentation, structured logically and clearly, includes all documents describing a technical product. It is also referred to as product documentation. All relevant information...
Weiterlesen
Final acceptance
Is carried out before delivery to the customer depending on the classification of the pressure equipment. Here, pressure equipment is to be subjected to the...
Weiterlesen
Flow rate
The flow rate (or flow velocity) is a physical size and defines the speed in a flow, in a directed movement of particles or in...
Weiterlesen
Forward acting rupture disc
Bursting discs are pressure relief devices protecting a vessel or a system from damaging high or low pressure by making a disposable membrane burst. Bursting...
Weiterlesen
Fouling
Refers to general contaminants / impurities. In relation to the heat exchanger, fouling may occur in the jacket area (heating medium) and in the product...
Weiterlesen
Fragmentation
The term fragmentation refers to the area characteristic of a bursting disc upon reaching the burst pressure. Depending on various factors, bursting discs may open...
Weiterlesen
Gas cushion (with reverse acting rupture discs)
When using reverse acting rupture discs it must be ensured that there is always a gas cushion between the bursting disc and the medium to...
Weiterlesen
Gas exchange area
Gas exchange is a physical process whereby gases (sometimes separated by a permeable membrane, sometimes by openings or pores) are spatially redistributed between two compartments,...
Weiterlesen
Goodness of mixture
The goodness of mixture is a measure of the homogeneity or uniformity of a mix and is calculated from statistic base items. The coefficient of...
Weiterlesen
Graphite bursting disc
The advantages of bursting discs made of graphite are their high resistance to corrosion, a good price-performance ratio and an easy assembly. Furthermore, they are...
Weiterlesen
Heat capacity
The relationship between the heat supplied to a body and the temperature rise resulting thereof is called the heat capacity C of the body: C...
Weiterlesen
Heat exchanger
The transfer of thermal energy from one material flow to another takes place in a suitable appliance, the heat exchanger. STRIKO heat exchangers are specially...
Weiterlesen
Holder (inlet and outlet part)
The use of bursting discs in bursting disc holders ensures the reliable functioning of the bursting discs. In the holder, the metallic sealing gasket between...
Weiterlesen
Integrated burst control
In order to reliably detect the reaction (opening) of bursting discs, burst indicators or leakage sensors can be used. These are usually installed between holder...
Weiterlesen
Leakage sensors
Leakage sensors are used in order to detect the smallest of leaks of bursting discs or safety valves. “Normal” burst indicators only react to the...
Weiterlesen
Mass flow
The term mass flow defines the fluid loading in kg/h being present in the gaseous phase intended to be separated....
Weiterlesen