Rupture Disc Equipment with integrated alarm / special solutions

Rupture Disc equipment with integrated alarms can be of diverse design. Either an inductive proximity switch is used that works in combination with other metal flags on the burst membrane, or the conductor path to be destroyed is directly integrated in the Rupture Disc, so that the amount of components can be further reduced. Special solutions such as extruder bursting discs with integrated breakage monitoring round off the STRIKO offer.

Alarm triggering by means of inductive proximity switches

With the help of inductive proximity switches the response of Rupture Disc can be economically and permanently monitored. For this purpose, the bursting disc holder is furnished with an inductive proximity switch which is opened by a metal flag attached to the burst membrane of the Rupture Disc. Once the Rupture Disc responds conventionally, the burst membrane turns together with the signal flag. Thus the bursting disc’s cross-sectional area will be opened as desired. At the same time, the opening of the Rupture Discis detected and the necessary measures may be taken.

By subsequently replacing the bursting disc the original status is restored; the signal flag mounted on the brand new bursting disc in front of the proximity switch safeguards the switch again and will keep it closed until the bursting disc device will respond anew. Choosing this solution means to invest only once in a bursting disc holder along with an inductive proximity switch. No additional costs will incur thereafter – except the usual ones for the replacement of the bursting disc. Consequently, spares and assembly costs will everlastingly decrease. On the contrary, when deciding in favour of the conventional solution with a bursting disc and a connected, separate burst indicator of the series SVT-02, not only the bursting disc but also the additional burst indicator must be replaced.

Design Examples

Details of alarm triggering by means of inductive proximity switches
Details of alarm triggering by means of inductive proximity switches

Advantages in the application

  1. Quick identification of a malfunction
  2. Simple assembly
  3. Maintenance-free
  4. Can be used in STRIKO standard bursting disc holders SHF and SHU
  5. Deliverable in nominal widths DN 25 to DN 400
  6. In every system it can be combined with STRIKO metal burst safety devices
  7. Continuous temperature range from -25° to +100°
  8. Design with inductive proximity switch


Switch element function

NUMUR opener

Rated voltage Uo

8,2 V

Reverse polarity and short circuit protected


Switch status display

all around LED, yellow

Ambient temperature

-25 … 100℃

Connecting cable

2 m PVC encased

Enclosure material

stainless steel

Protection category


NAMUR EN 60947-5-6:2000 / IEC 60947-5-2:2007


Electro-magnetic compatibility

NE 21:2007

ATEX certificate

1G; 2G; 3D; 3G

Note on ATEX:

All burst indicators / leakage sensors from STRIKO according to the type of protection are rated “i” intrinsic safety – “simple electrical equipment” when connected to an intrinsically safe circuit. The requirements on “simple electrical equipment” are covered in section 5.7 of the standards EN 60079-11:2012 or IEC 60079-11 Ed. 6:2011-06 “Explosive atmospheres – Part 11: Equipment protection by intrinsic safety ‘i'”. Simple electrical equipment, designed in accordance with the requirements of section 5.7 of the standards EN 60079-11:2012 or IEC 60079-11:2011 and section 16.4 of the standards EN 60079-14: 2014 or IEC 60079-14 Ed. 5: 2013-11 “Explosive atmospheres – Part 14: Electrical installations design, selection and erection” do not require certification; see section 4.4.2 of EN 60079-14: 2014 or IEC 60079-14 Ed. 5: 2013-11. Such parts are also not governed by directive 94/9/EC since they do not feature any potential source of ignition. The designation of simple equipment can be made by any person/institution, including the manufacturer or installer, and made by freely selectable designation marking or coding preferred for the installation/plant.

Your contact for Rupture Disc Equipment with integrated alarm / special solutions

Answering your questions precisely and competently - that is our goal.
Simply get in touch directly with your contacts from the divisions.


Marc Juckschat

Product Management
+49 2261 9855-18

Frank Stephan

Project Management
+49 2261 9855-25

Cornelia Raedel

Order Processing

Mandia Scheuse

Order Processing

Ardit Mimini

Order Processing
+49 2261 9855-26
STRIKO Request Form

Got a specific inquiry?

To Request Form